Pilot Carbon Column Filter Absorbent columns are used in the refining process to measure the absorption of various types of contaminants and chemical or physical parameters. The height and diameter of the pilot can be changed in terms of discharge and type of absorbent according to the design. Gravity and pressure can also be modeled and applied. Performance: This pilot column is an active carbon that drains upstream and out of it. Due to the porosity of the material inside the column and the gravity of the pilot, the flow rate will be limited. It is also possible to enter the wastewater from the bottom and exit it from the wastewater. The sample is internally filtered, aggregated and measured. By installing the sampler valves, there will be a possibility to sample from different points of the column and the efficiency of different sections.
[vc_row][vc_column][vc_column_text] This pilot was ordered by a master student of Khaje Nasir Tusi university in order to extract Kinetic parameters in industrial wastewater treatment plants using combine UASB and A2O methods. The pilot itself is consisted of two parts: 1- A UASB anaerobic unit including a process pillar with 20 mm diameter and 100 cm height as UASB reservoir, and 2- A wastewater treatment package using A2O method with general dimensions of 35*35*80 mm and 3 consecutive storage (anaerobic, aerobic, Anoxic). at the end a hopper sedimentation unit is used to deposit and return the sludge. An airlift system is used to return the combined liquids and sludge. This pilot has a 3 lit/sec capacity. A special multi dosing PLC control system was designed for this pilot.[/vc_column_text][/vc_column][/vc_row][vc_row][vc_column][vc_gallery type="image_grid" images="1436,1437,1321" img_size="120*120" css_animation="fadeInUp"][/vc_column][/vc_row]
[vc_row][vc_column][vc_column_text] This pilot was designed for a PhD thesis project in Ahvaz University. The capacity was 1~3 lit/hr with membrane technology. The model contained aeration and effluent storage tanks. Simple and low equipment design along with simple operating were key factors of this model. Membranes were provided by the costumer and flat sheet membrane design and fabrication were done in Rashab Tarh Company. [/vc_column_text][/vc_column][/vc_row][vc_row][vc_column][vc_gallery type="image_grid" images="1136,1137,1138" img_size="130*130" css_animation="fadeInUp"][/vc_column][/vc_row]
[vc_row][vc_column][vc_column_text] This pilot was designed and built for a PhD thesis project in Tehran University. The main goal of the project was to investigate the effect of electro Bio-reactor on the MBR wastewater treatment system and to reduce the rate of membrane fouling. The model contained two similar tanks with 1 lit/hr capacity. Two positive and negative electrodes were used in one of the tanks with changeable distance between them. It was possible to measure the membrane pressure and permeate flow. Total capacity for this system was1 lit/hr. [/vc_column_text][/vc_column][/vc_row][vc_row][vc_column][vc_gallery type="image_grid" images="1178,1179,1182,1180,1181,1185,1177,1183,1184,1186,1187,1188" img_size="120*120" css_animation="fadeInUp"][/vc_column][/vc_row]
[vc_row][vc_column][vc_column_text] This pilot was built for the IFA PAZHUHAN CO. to test the company's hollow fiber membranes. The pilot has the treatment capacity of 1 lit/hr constantly and it has equalization and aeration tanks. Also, all the equipments such as aeration, membrane suction pump and other control systems are installed on the device. [/vc_column_text][/vc_column][/vc_row][vc_row][vc_column][vc_gallery type="image_grid" images="1199,1200,1197,1196,1198,1201,1194,1195" img_size="120*120" css_animation="fadeInUp"][/vc_column][/vc_row]
[vc_row][vc_column][vc_column_text] This device was built to investigate the hydraulic uniform distribution systems of the fields. It was designed and built to answer the need for flow control and delivery to the users. It has the ability to measure the input pressure and to set, control and measure the flow at the same time. This device doesn't need any special equipments or electricity. [/vc_column_text][/vc_column][/vc_row][vc_row][vc_column][vc_gallery type="image_grid" images="1210,1209,1211" img_size="120*120" css_animation="fadeInUp"][/vc_column][/vc_row]
[vc_row][vc_column][vc_column_text] The device was built for a PHD student of Shahid Beheshti University. the thesis was "The Removal of Pathogenic Agents From Water's Micro plastics with UV Lamps". This study required uniform temperature (up to 80˚C) along with 9 housings with magnetic stirrer. more over, each house should be able to set the amount of rounds per minute. Also, as the pilot needed UV lamps to examine the effect of disinfection, it became a new brand design. It has the automatic temperature control and all the necessary means to protect the operator from UV lamps. [/vc_column_text][/vc_column][/vc_row][vc_row][vc_column][vc_gallery type="image_grid" images="1231,1232,1234,1657" img_size="120*120" css_animation="fadeInUp"][/vc_column][/vc_row][vc_row][vc_column][vc_column_text][/vc_column_text][/vc_column][/vc_row]
[vc_row][vc_column][vc_column_text] This model is a multi-purpose water treatment plant pilot, capable of operating in high ranges of hydraulically conditions and operational controls. the model has the capability of increasing or decreasing different modules in one process. Continuous operating is an advantage of this model. Currently, this model is used to investigate the effect of red mud in nitrate removal. Operational process: This pilot is consisted of different parts in order to replace and remove, and is capable of crating different hydraulically and operational conditions. It contains coagulation, flocculation, sedimentation, sludge and effluent storage systems and thus increasing the number of modules will be really easy. its possible to add or remove special equipment regarding the desired project. [/vc_column_text][/vc_column][/vc_row][vc_row][vc_column][vc_gallery type="image_grid" images="1220,1221,1222,1218,1219" img_size="120*120" css_animation="fadeInUp"][/vc_column][/vc_row][vc_row][vc_column][vc_column_text] [/vc_column_text][/vc_column][/vc_row]
[vc_row][vc_column][vc_column_text] The purpose of this model is to desalinate saline water and simultaneously treat wastewater and generate electricity. In this method compared to similar models, using advanced oxidation process, the amount of produced electricity and desalination is increased along with treatment speed. in this pilot, anionic and cationic membranes, carbide and titanium electrodes and a UV lamp were used. This model was designed for a phd student from university of Tehran. [/vc_column_text][/vc_column][/vc_row][vc_row][vc_column][vc_gallery type="image_grid" images="1156,1155,1154,1153,1152" img_size="130*130" css_animation="fadeInUp"][/vc_column][/vc_row]
[vc_row][vc_column][vc_column_text] This pilot was developed and commissioned by a PhD student from India. This pilot has been designed and built up to a refining capacity of 2 liters per sewage membrane. The balancing pond, aeration, MBR tank, sludge storage tank and wastewater storage tank are embedded in this pilot to complete the full-automatic and continuous system (Continuse). [/vc_column_text][/vc_column][/vc_row][vc_row][vc_column][vc_gallery type="image_grid" images="1298,1299,1304,1301,1302,1303,1300" img_size="120*120" css_animation="fadeInUp"][/vc_column][/vc_row]
